How To Clone Sd Card Serial Number

Here are some great tips and guides of GM MDI clone serial number update if you need to.

The GM MDIserial number is in the 16mb on board flash memory – the intel chip on the computer sub-board.

How To Clone Sd Card Serial Number

You can get u-boot access by making up a serial cable. Signals are available on the 8 pin mini din on the outside of the MDI case. pin 1 goes to PC TX (MDI
RX), pin 2 goes to PC RX (MDI TX). Pin 3 goes to ground. Then when you boot:

Quote:U-Boot 1.1.4 (Dec 21 2007 – 12:11:55) ETAS VCI
(r13006)

U-Boot code: A3F00000 -> A3F218F0 BSS: -> A3F27524
RAM Configuration: TRITON 270 II
Bank #0: a0000000 64 MB
Bank #1: a4000000 64 MB
HW Configuration: (0x207) MDI VCI with SMSC9116
Found P30 Flash, unlocking all blocks: 130
Flash: 16 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
$ help
? – alias for ‘help’
askenv – get environment variables from stdin
autoscr – run script from memory
base – print or set address offset
bdinfo – print Board Info structure
boot – boot default, i.e., run ‘bootcmd’
bootd – boot default, i.e., run ‘bootcmd’
bootm – boot application image from memory
bootp – boot image via network using BootP/TFTP protocol
cmp – memory compare
coninfo – print console devices and information
cp – memory copy
crc32 – checksum calculation
dhcp – invoke DHCP client to obtain IP/boot params
echo – echo args to console
erase – erase FLASH memory
exit – exit script
flinfo – print FLASH memory information
flock – physical lock of Strataflash
funlock – physical unlock of Strataflash
go – start application at address ‘addr’
help – print online help
iminfo – print header information for application image
imls – list all images found in flash
increnv – increment environment variables
itest – return true/false on integer compare
loadb – load binary file over serial line (kermit mode)
loads – load S-Record file over serial line
loop – infinite loop on address range
macaddr – display or store MAC address in Strataflash
mapadd – add a memory map item
mapdel – delete a memory map item
mapinfo – display the memory map information
md – memory display
mm – memory modify (auto-incrementing)
mmcinfo – get info on mmc(sd) card
mtest – simple RAM test
mw – memory write (fill)
nfs – boot image via network using NFS protocol
nm – memory modify (constant address)
ping – send ICMP ECHO_REQUEST to network host
pinit – PCMCIA sub-system
printenv- print environment variables
protect – enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset – Perform RESET of the CPU
run – run commands in an environment variable
saveenv – save environment variables to persistent storage
serialnum – display or store serial number in Strataflash
setenv – set environment variables
sleep – delay execution for some time
test – minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
version – print monitor version


The problem is the serial number and MAC flash partitions are misaligned from
the flash erase block boundaries, which forces them to mount read only. Because
of this the update commands don’t work 😭

$ serialnum
Serial number: 1220-22129579
$ serialnum 1220-12345678
Error: start address not on sector boundary
Failed to read same serial number back from Strataflash

Go to Settings and then click ABOUT. On top you will see Device ID: 10 digit number, which is the Card ID of the SD Card inserted. Unfortunately if you change your SD card it will always show the same number, at least in my case. So try with the right card first. At least you will get the ID of one SD Card. 2 days ago  How To Clone Sd Card Serial Number 8,5/10 3889 reviews Is there a way to read the CID of a micro-SD card. Rechargeable battery 600 mAh 8. VXX) for the SD card. Clone SD Card to Smaller SD card. For those of you having problems locating the new files for a china clone Kess v2 running version Open case of Kess v2 and locate SD/TF card. Run the tool and point it to the SD card device e.g. /dev/block/mmcblk1 (you almost certainly do not want to use mmcblk0, that is likely to be the built-in storage on your device). List the /dev/block folder and make sure the device you going to use appears and disappears as you insert and remove the SD card to be sure.


I think that if we mapped a memory partition at 0x00FE0000 with size 0x00020000
then we would be able to erase that partition and load a new one via ethernet /
tftp. This 128k block would cover both the serial and mac paritions. Both these
partitions have checksums which would need to be figured out and calculated.

What you have been editing is the equivalent of the MDI registry. Once the
serial and mac are changed in flash then a re-flash of the device should put
the new numbers in the registry and they should persist over device firmware
updates. I expect duplicate mac addresses are as relevant as the serial number
duplicates on your lan.

That location is with the entire SD card being read with a hex editor. If you can read the file then look at the end of registry.dat file. The serial number is 16 pairs of hex numbers. Anyone with a clone probably has “4E 2E 4D 95 AA 5D F3 F1 C7 3C 44 B9 97 55 A4 19” which somehow translates to 22129579.

Quote:$ mapinfo
Name Location Size Type Source Guard
—- ——– —- —- —— —–
boot 0x00000000 0x00040000 Flash bootargs Off
bootvars 0x00040000 0x00020000 Flash bootargs Off
linux1 0x00060000 0x00180000 Flash bootargs Off
initrd1 0x001e0000 0x00600000 Flash bootargs Off
linux2 0x007e0000 0x00180000 Flash bootargs Off
initrd2 0x00960000 0x00600000 Flash bootargs Off
linuxvars1 0x00f60000 0x00020000 Flash bootargs Off
linuxvars2 0x00f80000 0x00020000 Flash bootargs Off
serialnum 0x00ff0000 0x00008000 Flash bootargs Off
macaddress 0x00ff8000 0x00008000 Flash bootargs Off
zImage 0xa0008000 0x00200000 DRAM Initial Off
scratch 0xa2000000 0x00a00000 DRAM Initial Off
script 0xa2a00000 0x00100000 DRAM Initial Off
Stack 0xa3e9ff80 0x00020000 DRAM System On
GD 0xa3ebff80 0x00000080 DRAM System On
Heap 0xa3ec0000 0x00040000 DRAM System On
Text 0xa3f00000 0x000218f0 DRAM System On
BSS 0xa3f218f0 0x00005c34 DRAM System On

Number


The sdcard is just the /usr/local/ portion of the firmware. The rest is in the
16mb flash.

Be careful, its super easy to brick your MDI Interface with these tools.

Figured it out.

Mount the sdcard parition 1 under linux, and rename telnetd.sh-disabled to
telnet.sh in /bin. While there I also edited the init script and added this
near the start to make the prompt nicer:


Access u-boot (38400 baud, see previous post), and at the prompt type:

Quote:askenv setbootargsprimary

How To Clone Sd Card Serial Number Lookup

Please enter ‘setbootargsprimary’:run normalargs addinit addconsole addeth
addprimary;setenv bootargs ${bootargs}
mtdparts=flash0:256k(boot),128k(bootvars),1536k(linux1),6144k(initrd1),1536k(linux2),6144k(initrd2),128k(linuxvars1),128k(linuxvars2),32k@16320k(serialnum),32k(macaddress),128k@16256k(id);

boot


The MDI will boot and start a telnet server on its IP and have a new flash
partition configured as /dev/mtd10 called ‘id’. This will align with the erase
block so can be updated. Check in /var/log/messages for the presence of ‘id’
without it being forced readonly.

Telnet in and rip a copy of mtd10 with dd, and send it to an ftp server you
have setup on your lan.

Quote:[root@mdi~]# cd /tmp
[root@mditmp]# dd if=/dev/mtd10 of=mtd10.img
256+0 records in
256+0 records out
[root@mditmp]# ls -l mtd10.img
-rw-r–r– 1 root root 131072 Jan 1 00:07 mtd10.img
[root@mditmp]# ftpput -u <user> -p <pass>
<ip> mtd10.img mtd10.img


Now load up mtd10.img on your pc in HxD or Hexworkshop. The serial is at
0x10000 with a crc32 checksum of 0x10000->0x17FFB at 17FFC (LSB).

MAC is at 18000 with a crc32 checksum 0x18000->0x1FFFB at 1FFFC.

Update both (just change the last couple of numbers), and use the calculate
checksum feature of the hexeditor to calculate crc32 the sums of of the ranges
and save the new sums in the bin (remember to enter them in LSB format).

Now pull the files back to the mdi, and update flash:

Quote:[root@mdi~]# cd /tmp
[root@mditmp]# ftpget -u <user> -p <pass>
<ip> mtd10-new.img mtd10-new.img
[root@mditmp]# cd /usr/local/mtd/
[root@mdimtd]# ./flash_unlock /dev/mtd10
[root@mdimtd]# ./flash_erase /dev/mtd10
Erase Total 1 Units
Performing Flash Erase of length 131072 at offset 0x0 done
[root@mdimtd]# ./flashcp /tmp/mtd10-new.img /dev/mtd10
[root@mdimtd]# dd if=/dev/mtd10
of=/tmp/mtd10-readback.img
256+0 records in
256+0 records out
[root@mdimtd]# md5sum /tmp/mtd10-new.img
/tmp/mtd10-readback.img
1a1f4fb7db878218c558b45c0db50c9f /tmp/mtd10-new.img
1a1f4fb7db878218c558b45c0db50c9f /tmp/mtd10-readback.img


Now reboot the MDI,
and hold down the power button so it goes in to recovery mode. Use MDI manager
to recover the device. Once completed it’ll have the new serial and mac.

I expect that the cloners will find this thread and soon they won’t all have
the same serial anymore. But if you already have one then you can do this
yourself, so long as your careful and make sure everything is going to plan and
makes sense to you as you go.

(Many many many thanks to gmtools at
https://mhhauto.com/Thread-GM-MDI-serial-number?)

who like this article also viewed:

Recover an SD Card

If you deleted photos from a SD card mistakenly, or formatted a card inadvertently, or some pictures on the SD card missed for any reasons, you may need to find a SD Card Recovery software to recover the lost files from the SD card.

CardRecovery software from WinRecovery Software is the leading SD Card Recovery software to recover deleted files from SD card, or files lost due to other reasons. Both Windows and Mac versions are available.

Free Evaluation Version (Trial Version) Download

Windows: https://www.cardrecovery.com

Mac: https://www.cardrescue.com

Other SD card recovery software includes Rescue Pro Software, PhotoRec Software …

Flash an SD Card

When you need to save a system to a Raspberry Pi SD card, or similar device, direct copy does not work. You need a tool to flash the operation system image file to an SD card.

balena Etcher is a software tool to flash OS images to SD cards and flash drives.

Etcher is available for Windows, Mac and Linux platforms.

Downloads: https://www.balena.io/etcher/

Format an SD Card

To use a new SD card in cameras, phones or other devices, it is better to format it first, otherwise, the SD card may be not supported by the new device, or it does not work in best performance. It is recommended to use the SD Memory Card Formatter to format SD Cards rather than using formatting tools provided with Windows or Mac OS.

SD Memory Card Formatter

Formatting is the process to create a new file system on the disk, memory card, or flash drives.

Common File Systems:

  • NTFS: NTFS is the file system that Windows uses by default.
  • HFS+: The Hierarchical File System is usually the mainfile system used by macOS.
  • APFS: It is an Apple file system developed as a replacement for HFS+, with a focus on flash drives, SSDs, and encryption. It is used in the new iPhone OS.
  • FAT32, exFAT: FAT32 and exFAT are the popular and standard file systems used by digital cameras and portable devices.
  • EXT 2, 3, & 4: The extended file systems (EXT) are usually used by Linux.

Check an SD Card

H2Testw

How To Clone Sd Card Serial Number N1996

There are fake SD cards in the market, e.g. you bought a 128 GB SD card but actually, it is a 16 GB Card with faked labels. If you use it in a digital camera, the card of course stores much less photos and videos, it may also cause data loss and your valuable photos may be lost. You may need a tool to test and detect fake or counterfeit SD cards, or perhaps you just want to test an older storage device for errors and problems. H2Testw is a freeware tool designed to test the card capacity, read/write speed of an SD card, or scan and check for errors.

H2Testw can be downloaded from

How To Clone Sd Card Serial Number Lookup

Clone an SD Card

Sandisk Sd Card Serial Number

Sometimes, you may need to make a extra copy of an SD Card for backup or other purpose. Win32 Disk Imager is a Windows tool for reading data from an SD card and writing to a image file, also, it can be used to write a image file to a SD card. You may first use it to create a image file from a “Master” SD card, then write the image back to a different SD card to complete the SD card clone.

Download:

Clone Sd Card Serial Number

Important note: flashing, formatting or some SD card cloning and checking tool will wipe the data on the SD completely. So please use those tools carefully.